Research / 2019 / Article

Research Article | Open Access

Volume 2019 |Article ID 5385763 |

Zhiwang Zhang, Ye Gu, Houyou Long, Ying Cheng, Xiaojun Liu, Johan Christensen, "Subwavelength Acoustic Valley-Hall Topological Insulators Using Soda Cans Honeycomb Lattices", Research, vol. 2019, Article ID 5385763, 8 pages, 2019.

Subwavelength Acoustic Valley-Hall Topological Insulators Using Soda Cans Honeycomb Lattices

Received19 Apr 2019
Accepted16 Jul 2019
Published08 Aug 2019


Topological valley-contrasting physics has attracted great attention in exploring the use of the valley degree of freedom as a promising carrier of information. Recently, this concept has been extended to acoustic systems to obtain nonbackscattering sound propagations. However, previous demonstrations are limited by the cut-off frequency of 2D waveguides and lattice-scale size restrictions since the topological edge states originate from Bragg interference. Here we engineer topologically valley-projected edge states in the form of spoof surface acoustic waves that confine along the surface of a subwavelength honeycomb lattice composed of 330-mL soda cans. The inversion symmetry is broken through injecting a certain amount of water into one of the two cans in each unit cell, which gaps the Dirac cone and ultimately leads to the topological valley-Hall phase transition. Dual-frequency ranges of the valley-projected edge states below the sound line are observed, which originate from the first-order and second-order resonances, respectively. These results have the potential to enable promising routes to design integrated acoustic devices based on valley-contrasting physics.

Valleytronics [18], as a portmanteau of valley and electronics, was proposed to achieve the quantum manipulation over the valley degree of freedom, towards establishing a valley-spin-based technology that enables quantum computation [3, 4], valley selective excitation [5, 6], and topologically protected edge states [7, 8]. Over the past few years, this concept has also stimulated the analogous search for the topological valley-contrasting physics in classical systems, such as optics [912], acoustics [1320], and mechanics [2125]. Lu et al. introduced the vortex nature of the pseudospin valley states into the phononic crystal (PnC) [13] and experimentally demonstrated the existence of the topologically valley-projected edge states (TVPES) [14]. To extend the concept of topological order to the functional devices, a reconfigurable acoustic delay line [16] and a duplex directional acoustic antenna [17] based on TVPES have been experimentally demonstrated. However, all of these previous studies about TVPES entail several limiting factors. First, the aforementioned systems have been tested in closed waveguides of finite heights, which naturally sets a bound to the spectral window induced by the inevitable cut-off frequency. Second, sound waves can only be manipulated on lattice scales comparable to the operation wavelength as the TVPES originate from Bragg interferences. Consequently, systems based on subwavelength lattices supporting TVPES in open space remains an elusive and unanswered key question in the community. On the other hand, Lerosey et al. proposed a kind of soda cans metamaterial [2628], which acts as Helmholtz resonators at deep-subwavelength scales, to obtain spoof surface acoustic waves (SAWs) [29, 30]. Topological edge states analogous to the quantum spin-Hall effect have been theoretically demonstrated [31] in such system composed of soda cans metamaterial. However, to our knowledge, an experimental verification of topological edge states confined above the soda cans has yet not been reported.

In this work, we design a honeycomb lattice [32, 33] composed of 330-mL soda cans arrangement in free space, which supports a dual-frequency Dirac cone at the corner of the first Brillouin zone (BZ) near both the first-order and second-order resonance at the same time. We find that these two Dirac cones are both located below the sound line, which guarantees the propagation of spoof SAWs. By breaking the inversion symmetry of the unit cell by injecting a certain amount of water into one of the two cans in each cell, the degeneracy of the valley states is lifted and two complete band gaps can be obtained. We demonstrate that the band inversions take place when introducing different symmetry breaking schemes, which can be characterized by the topological valley phase transitions. Furthermore, following the bulk-edge correspondence [34], we experimentally verify the existence of TVPES between two soda can arrays of opposite valley-Chern indices and illustrate its robustness against sharp bends.

Let us start with a discussion on the Helmholtz-like soda can resonator. Figure 1(a) illustrates the basic schematic of such can having a height 13.02 cm, the radius 2.84 cm, and the neck length 0.2 cm. From the top view of the soda can, the neck can be considered as an ellipse with 1.25 cm and . The resonant frequency of the soda can is experimentally measured according to the standard test method ASTM E2611-09, of which the experimental setup is shown in Figure 1(b). As seen in Figure 1(c), the simulated first-order and second-order resonances are found near 402 Hz and 1465 Hz, respectively, which agree very well to corresponding experimental measurements: 402 Hz and 1442 Hz.

To achieve the single Dirac cone in the subwavelength scale, which is the necessary condition of the topological valley phase transition, the honeycomb PnC composed of multiple soda cans embedded in air is constructed as shown in Figure 2(a). Figure 2(b) shows the unit cell of PnC in the simulations containing two soda cans of heights and . The center-to-center distance between the two cans is 6.6 cm and the lattice constant is , which is 0.13 and 0.49 with / the corresponding wavelength of the first/second resonance, respectively. The velocity and mass density of air are 343 m/s and 1.21 . From the band diagrams in Figure 2(c), two single Dirac cones can be observed at the corners of the 1st BZ near the first-order and second-order resonance when the system is unperturbed (see gray circles in insets). Note that both Dirac cones are located below the sound line, which signifies the propagation of spoof SAWs confined to the array. However, in order to open the degeneracy, a perturbation should be introduced to break the inversion symmetry in the unit cell. Here the height difference between two cans is defined as . In practical terms though, we inject water into the cans to change the effective height. Owing to the inexistence of the inversion symmetry after introducing 0.2 cm, which means injecting 5-mL water into the can B only with A unchanged, the degenerated valley states based on the resonance of different orders are lifted to open a bulk band gap at the same time (see red dots in insets). As a result, two pairs of valley states (/ and /) exist at the K point below the sound line. Distributions of the total pressure fields and the sound intensity of four valley states are illustrated in Figure 2(d). The intensity vector is defined as , where p represents the pressure amplitude and the vector represents the sound velocity derived from the acoustic momentum equation. Three points should be noted. (i) The distributions of total pressure fields verify that the valley states / are induced by the first-order resonance and / are based on the second-order resonance. (ii) The sound intensity is strongly confined at the interface between the cans and free space, which verifies the propagation of spoof SAWs along the surface of the can array. (iii) The sound intensity of these valley states possesses the intrinsic circular polarized orbital angular momentum, which is also known as valley pseudospins. At and states, the sound field is left-handed circular polarized (LCP). Conversely, the acoustic vortex chiralities are right-handed circular polarized (RCP) at and states. Although just the eigenstates at K valley are considered here, we demonstrate that the counterparts at valley possess invariant vortex but opposite chirality because of the time-reversal symmetry, which are not shown.

We demonstrate that the vortex chiralities of the corresponding valley states will be inverted if the inversion symmetry is introduced oppositely, for instance, changing the sign of to 0.2 cm by injecting 5-mL water into the can A only with B unchanged. In Figure 3(a), eigenmodes of and valley states with different signs of are illustrated. The inversion of the chiralities can be clearly seen by means of the band inversion. Figure 3(b) shows that the eigenfrequencies of the valley states / separate the band gap at K point as a function of . The purple and green lines with dots represent the valley states with LCP and RCP chiralities, respectively. Note that the chirality/band inversions can be also observed between and valley states, which are induced by the second-order resonance, as shown in Figures 3(c) and 3(d). As a result, the dual band inversions below the sound line are obtained in the proposed soda can PnC. Further, we demonstrate that the band inversion leads to a topological phase transition between different valleys, of which the topological invariant is described by valley-Chern indices. Derived from the kp perturbation method, the effective Hamiltonian near the Dirac cone can be described as [14]where is the group velocity, k   is the distance from the Dirac points, is Pauli matrices of the vortex, and is the effective mass defined as . After the integral of the nontrivial Berry curvature over an individual valley, the nonvanishing valley-Chern indices can be determined by [8, 14]From (2) and Figure 3, we can conclude that the sign of the effective mass depends on the sign of height difference , which is shown in Figures 3(b) and 3(d). Furthermore, the valley indices of structure I () and structure II () are and , respectively.

According to the bulk-boundary correspondence, helical edge states can exist at the interface where the effective mass changes sign. For example, the difference of the topological valley indices across the interface I-II is , which supports an edge state projected by the K valley propagating with negative group velocity. Correspondingly, the edge state projected by the K valley has a positive group velocity along the interface II-I with . To verify the above predictions, the band diagrams of a ribbon structure with zigzag-type interface composed of 6 unit cells with different topological valley phase at either side are illustrated in Figure 4. A corresponding dispersion relation of the ribbon-shaped PnC with the armchair-type interface is discussed in the Supplementary Material Note I. The first-order resonance induced edge states are shown in Figures 4(a)–4(c). For the interface I-II (blue dots), a backward-moving edge state projected by K valley has been predicted as shown in Figure 4(b). On the other hand, a forward-moving edge state projected by K valley is sustained along the interface II-I (red dots) as shown in Figure 4(c). Both results are good agreement with theoretical predictions. In addition, the edge states are not gapless in this situation, which is different from previous reports [14, 16]. We demonstrate that the soda can PnC with the perturbation 0.2 cm is distorted to a relatively large level, which leads to the existence of the gapped valley-projected edge states. Note that the same perturbation has a stronger influence on the edge states pertaining to the second-order resonance whose band diagrams and the eigenmodes with different types of interfaces are illustrated in Figures 4(d)–4(f). Interestingly, the band of the edge state for the I-II seen in Figure 4(d) is almost entirely flat, which supports ultra-slow spoof SAW propagations useful for topological acoustic buffering [16].

To experimentally verify the existence of the TVPES, we construct a PnC composed of 12 soda can arrays as shown in Figure 5(a). The structures with opposite valley-Hall phases, which consist of red/green soda cans, are separated by a straight interface. In the simulations, one monopolar point source, which is marked by a red star in Figure 5(b), is placed at the left termination of the interface with a distance of 0.5 cm to the surface of the soda cans. The experimental details can be found in Supplementary Material Note II. Figure 5(b) illustrates the simulated absolute pressure fields at frequency Hz within the topological band gap. The sound waves transport along the interface and decay exponentially into the bulk. To experimentally verify it, we measure the normalized sound energy along a cutline in the middle of the PnC [red dashed line in Figure 5(b)], which is illustrated in Figure 5(c) together with the simulated results. Note that the distance between the y-direction cutline and the soda can arrays is 0.5 cm and the measured cutline crosses over the mouths of 12 soda cans, of which the experimental details are illustrated in the Supplementary Material Note II. As can be observed, the energy peak at the interface and the good agreement between the simulated and experimental results confirm the existence of the TVPES. The in-plane energy decay lengths towards two regions, which can be observed from Figure 5(c), are 0.15 and 0.11, indicating the tight confinement of TVPES at the interface. The slight disagreement between the predicted and observed energy profile results from the scattering by the experimental environment. Furthermore, we measure the amplitude of the acoustic pressure fields along the z direction away from one soda can, which is near the interface and indicated by a yellow ellipse in Figure 5(b). From the simulated and measured results at frequency f = 401.8 Hz shown in Figure 5(d), we demonstrate that the acoustic field is indeed confined to the surface and decays into free space exponentially, verifying the surface confined nature of the spoof SAW propagating in the form of a TVPES.

The hallmark of the physical properties of topological edge states is its robustness against defects as we will discuss in the following. Figure 6(a) illustrates the PnC with a -bended interface between two regions. The simulated distributions of the pressure fields at frequency f = 401.8 Hz indicate that sound waves transport along the route without backscattering even when the sharp bend is introduced. In the experiment, we measure the absolute pressure profiles along a cutline as shown in Figure 6(a), of which the data are illustrated in Figure 6(b) together with the simulated results. The agreement between the simulated and the experimental results verifies the robustness of the TVPES against the sharp bend. We demonstrate that the slightly increased pressure amplitude near the top termination of the cutline results from the scattering induced by the experimental environment. To further corroborate the robustness of the system, we introduce two sharp bends into a larger PnC composed of a 16 soda cans array. Figure 6(c) shows the simulated absolute pressure fields, from which sound waves transporting along the bended route without backscattering can be clearly observed. TVPES induced by the second-order resonance is discussed in Supplementary Material Note III.

To conclude, we have demonstrated a spoof SAW-based subwavelength valley-Hall topological insulator by arranging a honeycomb pattern of soda cans in open space. The topological valley-Hall phase transitions can be generated when the inversion symmetry is broken, simply by injecting water into the cans. Our experimental verification unequivocally demonstrates how spoof SAWs in soda cans lattices can confine along the interface between two distinct insulators in the form of topologically valley-projected edge states. Furthermore, the robustness against two sharp bends reassures the resilience of these novel surface waves. The proposed results may provide yet unseen possibilities to employ topological valley-contrasting acoustics in free space for audible sound control and guiding.

Conflicts of Interest

The authors declare that they have no conflicts of interest.


This work was supported by National Key R&D Program of China (2017YFA0303702), NSFC (11834008, 11874215, 11674172, and 11574148), Jiangsu Provincial NSF (BK20160018), the Fundamental Research Funds for the Central Universities (020414380001), and Nanjing University Innovation and Creative Program for PhD candidate (CXCY17-11). Zhiwang Zhang acknowledges the support from the China Scholarship Council. Johan Christensen acknowledges the support from the European Research Council (ERC) through the Starting Grant 714577 PHONOMETA and from the MINECO through a Ramón y Cajal grant (Grant no. RYC-2015-17156).

Supplementary Materials

Figure 1: (a) dispersion relation of the ribbon-shaped PnC with the armchair-type interface near the frequency of the first-order resonance. Gray circles represent bulk states and red dots represent the edge states; (b)-(c) distributions of the absolute pressure fields at . Figure 2: photographs of the placements of (a) the loudspeaker and (b) the microphones in the experiments. Figure 3: simulated distributions of the absolute pressure fields at the frequency = 1463.5 Hz (a) along the straight interface and (b) along the bended interface, respectively. (Supplementary Materials)


  1. A. Rycerz, J. Tworzydlo, and C. Beenakker, “Valley filter and valley valve in graphene,” Nature Physics, vol. 3, no. 3, pp. 172–175, 2007. View at: Google Scholar
  2. D. Xiao, W. Yao, and Q. Niu, “Valley-contrasting physics in graphene: magnetic moment and topological transport,” Physical Review Letters, vol. 99, Article ID 236809, 2007. View at: Publisher Site | Google Scholar
  3. D. Culcer, A. Saraiva, B. Koiller, X. Hu, and S. D. Sarma, “Valley-based noise-resistant quantum computation using Si quantum dots,” Physical Review Letters, vol. 108, Article ID 126804, 2012. View at: Google Scholar
  4. E. A. Laird, F. Pei, and L. Kouwenhoven, “A valley-spin qubit in a carbon nanotube,” Nature Nanotechnology, vol. 8, no. 8, pp. 565–568, 2013. View at: Google Scholar
  5. H. Zeng, J. Dai, W. Yao, D. Xiao, and X. Cui, “Valley polarization in MoS2 monolayers by optical pumping,” Nature Nanotechnology, vol. 7, no. 8, pp. 490–493, 2012. View at: Google Scholar
  6. K. F. Mak, K. He, J. Shan, and T. F. Heinz, “Control of valley polarization in monolayer MoS2 by optical helicity,” Nature Nanotechnology, vol. 7, no. 8, pp. 494–498, 2012. View at: Google Scholar
  7. I. Martin, Y. M. Blanter, and A. Morpurgo, “Topological confinement in bilayer graphene,” Physical Review Letters, vol. 100, Article ID 036804, 2008. View at: Google Scholar
  8. F. Zhang, A. H. MacDonald, and E. J. Mele, “Valley Chern numbers and boundary modes in gapped bilayer graphene,” Proceedings of the National Academy of Sciences of the United States of America, vol. 110, pp. 10546–10551, 2013. View at: Google Scholar
  9. T. Ma and G. Shvets, “All-Si valley-Hall photonic topological insulator,” New Journal of Physics, vol. 18, Article ID 025012, 2016. View at: Google Scholar
  10. J.-W. Dong, X.-D. Chen, H. Zhu, Y. Wang, and X. Zhang, “Valley photonic crystals for control of spin and topology,” Nature Materials, vol. 16, no. 3, pp. 298–302, 2017. View at: Google Scholar
  11. X. Wu, Y. Meng, J. Tian et al., “Direct observation of valley-polarized topological edge states in designer surface plasmon crystals,” Nature Communications, vol. 8, article no 1304, 2017. View at: Google Scholar
  12. F. Gao, H. Xue, Z. Yang et al., “Topologically protected refraction of robust kink states in valley photonic crystals,” Nature Physics, vol. 14, no. 2, p. 140, 2018. View at: Google Scholar
  13. J. Lu, C. Qiu, M. Ke, and Z. Liu, “Valley vortex states in sonic crystals,” Physical Review Letters, vol. 116, Article ID 093901, 2016. View at: Google Scholar
  14. J. Lu, C. Qiu, L. Ye et al., “Observation of topological valley transport of sound in sonic crystals,” Nature Physics, vol. 13, pp. 369–374, 2017. View at: Google Scholar
  15. J. Lu, C. Qiu, W. Deng et al., “Valley topological phases in bilayer sonic crystals,” Physical Review Letters, vol. 120, no. 11, Article ID 116802, 2018. View at: Google Scholar
  16. Z. Zhang, Y. Tian, Y. Cheng, Q. Wei, X. Liu, and J. Christensen, “Topological acoustic delay line,” Physical Review Applied, vol. 9, Article ID 034032, 2018. View at: Google Scholar
  17. Z. Zhang, Y. Tian, Y. Wang et al., “Directional acoustic antennas based on valley-Hall topological insulators,” Advanced Materials, vol. 30, Article ID 1803229, 2018. View at: Google Scholar
  18. Y. Shen, C. Qiu, X. Cai et al., “Valley-projected edge modes observed in underwater sonic crystals,” Applied Physics Letters, vol. 114, Article ID 023501, 2019. View at: Google Scholar
  19. X. Zhang, M. Xiao, Y. Cheng, M.-H. Lu, and J. Christensen, “Topological sound,” Communications Physics, vol. 1, article no 97, 2018. View at: Google Scholar
  20. Z. Zhang, Y. Cheng, and X. Liu, “Achieving acoustic topological valley-Hall states by modulating the subwavelength honeycomb lattice,” Scientific Reports, vol. 8, article no 16784, 2018. View at: Google Scholar
  21. J. Vila, R. K. Pal, and M. Ruzzene, “Observation of topological valley modes in an elastic hexagonal lattice,” Physical Review B, vol. 96, Article ID 134307, 2017. View at: Google Scholar
  22. H. Zhu, T.-W. Liu, and F. Semperlotti, “Design and experimental observation of valley-Hall edge states in diatomic-graphene-like elastic waveguides,” Physical Review B, vol. 97, Article ID 174301, 2018. View at: Google Scholar
  23. J. Wang and J. Mei, “Topological valley-chiral edge states of Lamb waves in elastic thin plates,” Applied Physics Express, vol. 11, no. 5, Article ID 057302, 2018. View at: Google Scholar
  24. M. Yan, J. Lu, F. Li et al., “On-chip valley topological materials for elastic wave manipulation,” Nature Materials, vol. 17, no. 11, pp. 993–998, 2018. View at: Google Scholar
  25. G. Ma, M. Xiao, and C. Chan, “Topological phases in acoustic and mechanical systems,” Nature Reviews Physics, vol. 1, pp. 281–294, 2019. View at: Google Scholar
  26. F. Lemoult, M. Fink, and G. Lerosey, “Acoustic resonators for far-field control of sound on a subwavelength scale,” Physical Review Letters, vol. 107, Article ID 064301, 2011. View at: Google Scholar
  27. F. Lemoult, N. Kaina, M. Fink, and G. Lerosey, “Wave propagation control at the deep subwavelength scale in metamaterials,” Nature Physics, vol. 9, no. 1, p. 55, 2013. View at: Google Scholar
  28. N. Kaina, F. Lemoult, M. Fink, and G. Lerosey, “Negative refractive index and acoustic superlens from multiple scattering in single negative metamaterials,” Nature, vol. 525, no. 7567, pp. 77–81, 2015. View at: Publisher Site | Google Scholar
  29. J. Christensen, A. Fernandez-Dominguez, F. de Leon-Perez, L. Martin- Moreno, and F. Garcia-Vidal, “Collimation of sound assisted by acoustic surface waves,” Nature Physics, vol. 3, no. 12, pp. 851-852, 2007. View at: Google Scholar
  30. Z. He, H. Jia, C. Qiu et al., “Nonleaky surface acoustic waves on a textured rigid surface,” Physical Review B, vol. 83, Article ID 132101, 2011. View at: Google Scholar
  31. S. Yves, R. Fleury, F. Lemoult, M. Fink, and G. Lerosey, “Topological acoustic polaritons: robust sound manipulation at the subwavelength scale,” New Journal of Physics, vol. 19, no. 7, Article ID 075003, 2017. View at: Google Scholar
  32. Z. Zhang, Q. Wei, Y. Cheng, T. Zhang, D. Wu, and X. Liu, “Topological creation of acoustic pseudospin multipoles in a flow-free symmetry-broken metamaterial lattice,” Physical Review Letters, vol. 118, Article ID 084303, 2017. View at: Google Scholar
  33. Z. Zhang, Y. Tian, Y. Cheng, X. Liu, and J. Christensen, “Experimental verification of acoustic pseudospin multipoles in a symmetry-broken snowflakelike topological insulator,” Physical Review B, vol. 96, Article ID 241306, 2017. View at: Google Scholar
  34. M. Ezawa, “Topological Kirchhoff law and bulk-edge correspondence for valley Chern and spin-valley Chern numbers,” Physical Review B, vol. 88, Article ID 161406, 2013. View at: Google Scholar

Copyright © 2019 Zhiwang Zhang et al. Exclusive licensee Science and Technology Review Publishing House. Distributed under a Creative Commons Attribution License (CC BY 4.0).

1041 Views | 336 Downloads | 1 Citation
 PDF Download Citation Citation

Altmetric Attention Score

Find out more
 Sign up for content alerts