Research Article | Open Access
Jun Liu, Shi Chen, Hongya Wang, Shuang Zheng, Long Zhu, Andong Wang, Lulu Wang, Cheng Du, Jian Wang, "Amplifying Orbital Angular Momentum Modes in Ring-Core Erbium-Doped Fiber", Research, vol. 2020, Article ID 7623751, 12 pages, 2020. https://doi.org/10.34133/2020/7623751
Amplifying Orbital Angular Momentum Modes in Ring-Core Erbium-Doped Fiber
Lots of research efforts have been devoted to increase the transmission capacity in optical communications using orbital angular momentum (OAM) multiplexing. To enable long-haul OAM mode transmission, an in-line OAM fiber amplifier is desired. A ring-core fiber (RCF) is considered to be a preferable design for stable OAM mode propagation in the fiber. Here, we demonstrate an OAM fiber amplifier based on a fabricated ring-core erbium-doped fiber (RC-EDF). We characterize the performance of the RC-EDF-assisted OAM fiber amplifier and demonstrate its use in OAM multiplexing communications with OAM modes carrying quadrature phase-shift keying (QPSK) and quadrature amplitude modulation (QAM) signals. The amplification of two OAM modes over four wavelengths is demonstrated in a data-carrying OAM-division multiplexing and wavelength-division multiplexing system. The obtained results show favorable performance of the RC-EDF-assisted OAM fiber amplifier. These demonstrations may open up new perspectives for long-haul transmission in capacity scaling fiber-optic communications employing OAM modes.
Light beams carrying orbital angular momentum (OAM) are characterized by a helical phase front of , where is the topological charge and is related to the azimuthal angle. The handedness and twisting rate of the helical phase front are described by the sign and absolute value of the topological charge , respectively, which is an unlimited value in principle. Due to the helical phase structure, an OAM beam usually has a doughnut intensity profile with a phase singularity at the beam center. Because of these features, OAM beams have been widely used in optical manipulation, optical tweezers, microscopy and imaging, metrology, optical vortex knots, astronomy, and quantum information processing [2–14]. In the past few decades, optical communications employing OAM beams have also attracted increasing attention from researchers [15–21]. Similar to other mode bases in free space or in fiber [22–24], OAM beams with helical phase structure are another mode base related to the spatial domain. Thus, OAM-division multiplexing (OAM-DM), as a new multiplexing technique of space-division multiplexing (SDM), provides an alternative potential to enable the continuous increase of transmission capacity and spectral efficiency [15, 16, 25–31]. Ring-core fiber (RCF) with an annual refractive index profile has been proven to be a preferable design for stable propagation of OAM modes in fibers since being first demonstrated in 2009 . The index profile of RCF is compatible with the donut-shaped OAM fields which is beneficial to suppress the unwanted radially higher-order modes. This simplifies the multiplexing and demultiplexing of the OAM modes and prevents crossing between effective indices of modes belonging to different families, allowing good mode separation. In addition, comparing to a mode-division multiplexing (MDM) system using multimode fibers (MMFs), fiber-optic OAM multiplexing communications employing RCFs can simplify or even avoid the complex multiple-input multiple-output (MIMO) digital signal processing (DSP) traditionally used to mitigate the mode crosstalk [33–35]. In the last decade, optimized design of RCFs has led to a significant increase in the number of OAM modes and the length of RCFs in fiber-optic OAM multiplexing communication systems [33–35]. However, the transmission distances are still very short for practical applications and cannot be compared with the widely used commercial single-mode fiber (SMF) optical communication systems. One of the limitations is the lack of OAM amplifiers. Among various types of amplifiers, fiber-based optical amplifiers are preferable for their full compatibility with fiber-optic communications. Hence, an OAM fiber amplifier is also highly desired, and its use in a practical data-carrying OAM multiplexing communication system is of great importance. Furthermore, the theoretical analyses show that erbium-doped fiber (EDF) with a ring-core profile features larger mode gain and smaller differential modal gain (DMG) . In this scenario, a laudable goal would be to implement an OAM fiber amplifier based on the ring-core EDF (RC-EDF) with an annual refractive index profile.
In this paper, we propose and demonstrate an OAM fiber amplifier based on a fabricated RC-EDF. Two OAM modes (OAM+1 and OAM-1) each carrying a 10-Gbaud quadrature phase-shift keying (QPSK) or quadrature amplitude modulation (QAM) signal are multiplexed together and amplified by the RC-EDF-assisted OAM fiber amplifier. In addition, the compatibility of the RC-EDF-assisted OAM fiber amplifier with a wavelength-division multiplexing (WDM) system is evaluated by amplifying two OAM modes carrying 10-Gbaud QPSK signals over four wavelengths. Finally, we characterize in detail the performance of a single OAM mode carrying a 10-Gbaud QPSK/16-QAM signal at a different input signal power and launched pump power. The measured small-signal gain is above 14 dB from 1530 to 1565 nm. The obtained results show favorable performance of the RC-EDF-assisted OAM fiber amplifier in data-carrying OAM-DM and WDM systems.
2.1. Concept and Principle
The concept and principle of an OAM fiber amplifier based on a RC-EDF are illustrated in Figure 1(a). The multiplexed OAM modes are greatly attenuated after long-haul fiber transmission and are difficult to be directly demultiplexed and detected. The OAM fiber amplifier provides the necessary relay amplification for multiplexed OAM modes after lossy long-haul fiber transmission. The OAM fiber amplifier is based on a RC-EDF. We design and fabricate a RC-EDF with its refractive index profile depicted in Figure 1(b). The insert image is the measured optical microscope image of the fabricated RC-EDF facet. The RC-EDF has an inner ring diameter of 4 μm and outer ring diameter of 16 μm and a cladding diameter of 219 μm. The maximum refractive index difference between the ring core and silica cladding is 0.0057. The RC-EDF is designed to support OAM+1 and OAM-1 for an OAM-DM system.
The experimental configuration of the RC-EDF-assisted OAM fiber amplifier is schematically illustrated in Figure 1(c). OAM-1 and OAM+1 modes are generated by loading specific phase patterns onto two spatial light modulators (SLM1 and SLM2, respectively). The polarization of one OAM mode is rotated by 90° by a half-wave plate (HWP) after one SLM. Then, we use a polarization beam splitter (PBS) to combine the generated two linearly polarized OAM-1 and OAM+1 together. After that, the two OAM modes are converted into two circularly polarized OAM modes by the following quarter-wave plate (QWP). A 10x objective lens is used to couple the multiplexed OAM modes into a 1 m RC-EDF. Remarkably, to remove unwanted parasitic lasing, we cut obliquely at the fiber output. To reduce the potential Fresnel reflections and suppress the signal light propagation in the backward direction, we have two free-space isolators placed at both ends of the amplifier. A long-pass dichroic mirror (DMLP1180, Thorlabs, DM) is used to couple the 980 nm pump light into the RC-EDF, which is highly reflective below 1180 nm and highly transmissive above 1180 nm. To filter out residual pump beams, another DM is placed at the output. In addition, the input signal power () is measured at point A.
2.2. Performance Evaluation of RC-EDF-Assisted OAM Fiber Amplifier
We first characterize the performance of the RC-EDF-assisted OAM fiber amplifier. Figures 2(a) and 2(b) show the measured amplified spectra for OAM+1 and OAM-1 modes of the RC-EDF-assisted OAM fiber amplifier at an input signal power of 5 dBm and launched pump power of 550 mW. It is shown that more than 30 dB optical signal-to-noise ratio (OSNR) after amplification with an OSA resolution of 0.1 nm can be achieved in the experiment. Figures 2(c)–2(e) display the measured intensity profiles, interferograms, and demodulation of OAM+1 and OAM-1 modes after amplification by the RC-EDF-assisted OAM fiber amplifier at the wavelengths of 1540, 1550, and 1560 nm, respectively. The left and right parts show the measured results for OAM+1 and OAM-1 modes, respectively, which can be verified by the twisting direction of the interferograms. It is noted that the interferograms are obtained by interfering OAM modes with a reference left-hand or right-hand circularly polarized Gaussian beam.
We then measure the gain spectra for OAM+1 and OAM-1 modes at the output of the RC-EDF-assisted OAM fiber amplifier as a function of the wavelength from 1530 to 1565 nm, as shown in Figures 3(a) and 3(b). The pump power () is fixed at 550 mW while varies from -23 to 5 dBm. One can clearly see that the mode gain peak is located at 1560 nm with a maximum gain of 20.16 dB for the OAM+1 mode and 19.05 dB for the OAM-1 mode. In general, the mode gain reduces with the increase of the input signal power and the small-signal gain is up to 19 dB (). Similarly, we also measure the gain spectra for OAM+1 and OAM-1 modes as a function of the wavelength with increasing from 400 to 550 mW at a fixed equaling -10 dBm, as shown in Figures 3(c) and 3(d). One can see that the mode gains of the OAM+1 and OAM-1 modes increase with the pump power. The mode gain peak is located at 1540 nm in the simulation while the experimental peak wavelength is 1560 nm. The slight differences between the simulations (see Materials and Methods) and experiments might be explained by the fact that the gain spectrum is highly associated with the signal and pump power and fiber length . Additionally, the practical erbium-doping profile of the fabricated RC-EDF might be slightly different from the simulations adopting smooth interpolation curve calculated by five points.
2.3. Performance Evaluation of the Data-Carrying OAM-DM and WDM System Using RC-EDF-Assisted OAM Fiber Amplifier
Furthermore, we apply the RC-EDF-assisted OAM fiber amplifier to the OAM-DM and WDM system and evaluate its system-level performance. The measured bit-error rate (BER) curves as a function of the received OSNR of the multiplexed OAM+1 and OAM-1 modes carrying 10-Gbaud QPSK or 16-QAM signal for the single wavelength at 1540, 1550, and 1560 nm are shown in Figures 4(a) and 4(b), respectively. The is -15 dBm and the is 550 mW. The measured OAM+1- or OAM-1-only results without crosstalk (w/o crosstalk) are also depicted in Figure 4 for comparison with those with crosstalk (w/ crosstalk). For the 10-Gbaud QPSK signals, the measured OSNR penalties of demultiplexed OAM+1 and OAM-1 modes after amplification are about 0.5 dB w/o crosstalk and 1.5 dB w/ crosstalk at a BER of , the enhanced forward-error correction (EFEC) threshold, at the wavelength of 1540, 1550, and 1560 nm. The inserted images in Figure 4(a) depict measured typical constellations of 10-Gbaud QPSK signals for OAM+1 at 1540 nm, OAM-1 at 1550 nm, and OAM+1 at 1560 nm with crosstalk at a BER of . For 10-Gbaud 16-QAM signals, the measured OSNR penalties of demultiplexed OAM+1 and OAM-1 modes after amplification are about 1.5 dB w/o crosstalk and 2.8 dB w/crosstalk at a BER of , the 7% hard-decision forward error correction (FEC) threshold, at the wavelength of 1540, 1550, and 1560 nm. The inserted images in Figure 4(b) show measured typical constellations of 10-Gbaud 16-QAM signals for OAM-1 at 1540 nm, OAM+1 at 1550 nm, and OAM-1 at 1560 nm with crosstalk at a BER of . The obtained results indicate successful implementation of amplifying multiplexed data-carrying OAM modes with favorable system-level performance. Moreover, we measure the amplification performance of the data-carrying OAM-DM and WDM system. Figures 4(c) and 4(d) show the WDM spectra for OAM modes after amplification in which the four ITU-grid wavelengths are 1549.32 nm, 1550.12 nm, 1550.92 nm, and 1551.72 nm with a 100 GHz spacing. Figure 4(e) depicts the measured BER as a function of the received OSNR for multiplexed four wavelengths and two OAM modes carrying 10-Gbaud QPSK signals after amplification. The is -15 dBm and the is 550 mW. The measured OSNR penalties of all the 8 channels (OAM-DM+WDM) are less than 1.8 dB at a BER of . The inserted images in Figure 4(e) are recorded constellations of 10-Gbaud QPSK signals for OAM+1 at 1549.32 nm and 1550.92 nm and OAM-1 at 1550.12 nm and 1551.72 nm with crosstalk at a BER of . The obtained results indicate favorable performance of the data-carrying OAM-DM and WDM system using a RC-EDF-assisted OAM fiber amplifier.
We also measure the BER performance of a single OAM mode carrying a 10-Gbaud QPSK/16-QAM signal at a different input signal power and launched pump power. Figures 5(a) and 5(c) display the measured BER performance for a single OAM+1 and OAM-1 mode carrying 10-Gbaud QPSK and 16-QAM signal at a different input signal power, respectively. The is 550 mW and the wavelength is 1550 nm. The overall BER performance is dependent on the input signal power fed into the RC-EDF-assisted OAM fiber amplifier which affects the output OSNR. The measured OSNR penalties of OAM+1 and OAM-1 modes are about 0.1, 0.3, 0.5, and 0.8 dB for the QPSK signal at a BER of under different input signal powers of -5, -10, -15, and -20 dBm, respectively. The measured OSNR penalties of OAM+1 and OAM-1 modes are about 0.6, 1, 1.5, and 2.6 dB for the 16-QAM signal at a BER of under a different input signal power of -5, -10, -15, and -20 dBm, respectively. The inserted images are typical constellations of QPSK and 16-QAM signals with a different input signal power. Moreover, we also measure the BER performance for OAM+1 and OAM-1 modes carrying a 10-Gbaud QPSK and 16-QAM signal at the output of the RC-EDF-assisted OAM fiber amplifier as a function of the launched pump power, as shown in Figures 5(b) and 5(d). The input signal power is fixed at -15 dBm. The inserted images depict measured typical constellations of QPSK and 16-QAM signals carried by OAM+1 and OAM-1 modes under a different pump power. One can clearly see that the BER performance is dependent on the pump power. Low pump power can lead to a rapid degradation in the BER performance.
The obtained results shown in Figures 2–5 indicate successful implementation of the RC-EDF-assisted OAM fiber amplifier for single and multiplexed OAM modes and its applications in a data-carrying OAM-DM and WDM system with favorable performance.
In summary, we have proposed and demonstrated an RC-EDF-assisted OAM fiber amplifier, and its performance has been evaluated in a data-carrying OAM-DM and WDM system. The small-signal gain is up to 19 dB for both OAM+1 and OAM-1 modes at the wavelength of 1560 nm and above 14 dB from 1530 to 1565 nm (C band). When transmitting the 10-Gbaud QPSK signal, the measured OSNR penalties at a BER of for single wavelength at 1540, 1550, and 1560 nm are less than 1.5 dB in an OAM-DM only system, while less than 1.8 dB for all channels in an OAM-DM and WDM system. When transmitting a 10-Gbaud 16-QAM signal, the measured OSNR penalties at a BER of for a single wavelength at 1540, 1550, and 1560 nm are less than 2.8 dB in an OAM-DM only system. The overall BER performance is dependent on the input signal power and pump power fed into the OAM fiber amplifier. The obtained results indicate favorable performance of the OAM fiber amplifier based on RC-EDF. The demonstrated RC-EDF-assisted OAM fiber amplifier may open up added capacity scaling and long-haul transmission opportunities in high-speed optical communication systems employing OAM multiplexing. Remarkably, the OAM-DM is fully compatible with existing multiplexing techniques. In addition to the OAM-DM and WDM system, the RC-EDF-assisted OAM fiber amplifier can be also used in the OAM-DM system incorporating the polarization-division multiplexing (PDM) technique.
Beyond the proof-of-concept demonstration of the RC-EDF-assisted OAM amplifier in this work, it is essential to further improve the performance of the OAM fiber amplifier for practical use in long-haul OAM-DM communication systems. To further improve the performance of the RC-EDF, two issues need to be considered: (1) to support more OAM modes in the RC-EDF and (2) to enable large and uniform modal gain among different OAM modes, i.e., a specialty fiber providing large and uniform modal gain among more OAM modes is preferable. To increase the number of supported OAM modes, one way is to increase the refractive index difference between the fiber ring-core and cladding , i.e., high-index-contrast RC-EDF, and the other is to increase the ring width or position . Air-core EDF might be also considered to further increase the refractive index difference between the ring core and cladding . To enable large modal gain with low DMG over a wide wavelength range, the erbium-doping profile needs to be further optimized. For example, one can employ the RC-EDF design with two-layer erbium covering the sidewalls of the high-index region . The newly added degree of freedom of the erbium-doping profile benefits the performance improvement. Besides, one can also employ a higher-order pump mode rather than the Gaussian beam to improve the overlap between the signal and pump intensity profiles for more uniform amplifications. Furthermore, in order to realize an all-fiber OAM-DM system which is the ultimate goal of optical fiber communication systems employing OAM modes, there are still many challenges to be addressed, such as all-fiber OAM (de)multiplexer, low-loss and low-crosstalk splicing of the EDF with the OAM transmission fiber, OAM fiber isolator, and all-fiber OAM 980/1550 nm WDM coupler. For example, splicing the ED-RCF with an OAM transmission fiber (e.g., vortex fiber [16, 34]) is of great importance. This could be addressed by precisely matching the mode profiles between the RC-EDF and OAM transmission fiber when designing the RC-EDF.
4. Materials and Methods
4.1. Simulation Results of RC-EDF
We theoretically assess the mode gain by solving the rate and power propagation equations through the Runge-Kutta 4th-order method [39, 40]. In this work, the simulations are under the following conditions: (1) The RC-EDF-assisted OAM fiber amplifier is assumed to be fundamentally pumped at the 980 nm wavelength, (2) OAM+1 and OAM-1 modes are considered, (3) the bandwidth of amplified spontaneous emission (ASE) ranges from 1430 to 1640 nm with an interval of 1 nm. We derive a new set of equations to describe the RC-EDF as follows:
In equations (1)–(3), indicates different modes, and are the absorption and emission cross-sections, respectively; , , and are the erbium ion densities of the ground state, the metastable state, and the total erbium ion density; variables and designate the optical frequency and the ASE channel bandwidth centered at ; is the Planck constant; and is the lifetime of the metastable level of the erbium ions. is the normalized beam intensity profile calculated by using a full-vector finite-element mode solver. For the OAM+1 and OAM-1 modes, is obtained by combining the fiber eigenmodes in the form of . By solving equations (1)–(3) through the Runge-Kutta 4th-order calculation, the gain for OAM+1 and OAM-1 modes of RC-EDF can be assessed.
The measured refractive index profile and erbium-doping profile of the fabricated RC-EDF are plotted in Figure 6(a). The index profile of Figure 6(a) is plotted with the different scale from Figure 1(b) in the radius, which depicts the ring-core structure more clearly. The five red solid circles are the measured erbium ion doping concentration in five radial positions, and the red dashed line is the related smooth interpolation curve for simulation. The simulated results of OAM+1 and OAM-1 modes supported in the fabricated RC-EDF are shown in Figure 6(b) in the upper and lower rows, respectively. The 3D intensity profiles, 2D intensity profiles, and phase profiles at the cross-section of OAM+1 and OAM-1 modes are displayed in the first column, second column, and third column, respectively. One can clearly see the doughnut intensity profiles due to the phase singularity at the beam center.
Figures 6(c)–6(f) plot the simulated mode gain of OAM+1 and OAM-1 modes based on the smooth interpolation curve of the erbium-doping profile shown in Figure 6(a). The parameters of the RC-EDF-assisted OAM fiber amplifier used in simulations are as follows. The fiber length is 1 m, pump power is 150 mW, signal power is -10 dBm, and the signal wavelength is 1550 nm. The gain is simulated by scanning one of the parameters with the others fixed as above. For example, Figure 6(c) shows the gain for OAM+1 and OAM-1 modes versus fiber length with pump power, signal power, and wavelength fixed at 150 mW, -10 dBm, and 1550 nm, respectively. The gain for the OAM+1 and OAM-1 modes is 15.38 dB with a fiber length of 1 m. Similarly, when fixing the fiber length at 1 m, the gains for OAM+1 and OAM-1 modes versus signal power, pump power, and wavelength are shown in Figures 6(d)–6(f), respectively. One can see that the gain increases with the pump power, while the growth rate becomes relatively slow with larger pump power. The smaller signal power benefits larger gain. The gain peak is located at ~1540 nm with the maximum gain of 18.54 dB for the OAM+1 and OAM-1 modes over the whole C band.
4.2. Experimental Realization
The detailed experimental setup of the RC-EDF-assisted OAM fiber amplifier in data-carrying OAM-DM and WDM systems is shown in Figure 7, which consists of five parts (transmitter, multiplexing of OAM modes, OAM fiber amplifier based on RC-EDF, demultiplexing of OAM modes, and receiver). At the transmitter side, a 10-Gbaud QPSK or 16-QAM signal is generated by the tunable laser followed by an optical I/Q modulator, which is fed by an arbitrary waveform generator (AWG, Tektronix AWG70002) with programmed 10-Gbaud QPSK/16-QAM electric signal. A laser at a wavelength of 1540, 1550, or 1560 nm is used as the optical source for the single wavelength system. Four lasers at wavelengths of 1549.32, 1550.12, 1550.92, and 1551.72 nm are employed as optical sources for a typical 100 GHz ITU-grid WDM system. In the multiplexing part, before incident to the SLMs, the light beam is split into two paths, relatively delayed by a piece of SMF for decorrelation, and amplified by erbium-doped fiber amplifiers (EDFAs). The following part is an OAM fiber amplifier assisted by a RC-EDF, which is described in Figure 1(c). A polarization controller on RC-EDF (PC-RC-EDF) is used to mitigate the mode crosstalk. After being amplified by the RC-EDF-assisted OAM fiber amplifier, the OAM modes are collected by a 20x objective lens and converted back to a Gaussian-like beam by another SLM loaded with a specific phase pattern. A camera is used in the multiplexing and demultiplexing parts to observe the intensity distributions of output light beams of the OAM fiber amplifier and demodulated OAM modes.
At the receiver side (coherent detection), the back-converted Gaussian-like beam with a bright spot at the beam center is coupled into an SMF, amplified by a second EDFA. A tunable filter is used to suppress the ASE noise. A variable optical attenuator (VOA) followed by a third EDFA are then used to adjust the received OSNR for BER performance measurement. Another tunable laser serves as a local oscillator (LO) to mix with the received signal by an optical hybrid, the outputs of which are sent to an oscilloscope followed by offline DSP. To characterize the performance of the OAM fiber amplifier, an additional part is set for measuring amplified spectra of the RC-EDF-assisted OAM fiber amplifier before the demultiplexing part. The input signal power () is measured by a free-space power meter (PM100D, S132C) at the point A before the 10x objective lens. The output light beams after amplification are collected by a MMF and fed into the optical spectrum analyzer (OSA, Yokogawa AQ6370C). To eliminate effects of the noise fluctuation with the input signal power and pump power, the output power () is measured by an OSA at the range of 10 nm around the input signal wavelength. Considering the loss of optical elements (objective lens, lens, isolator, QWP, and DM) and the coupling loss of RC-EDF (), the gain of the OAM fiber amplifier can be indicated as . By scanning the input wavelength at an interval of 5 nm, we can get the gain at different wavelengths and then plot the amplified spectra of the RC-EDF-assisted OAM fiber amplifier.
Conflicts of Interest
The authors declare that there is no conflict of interest regarding the publication of this article.
J.W. developed the concept and conceived the experiment. C.D. fabricated the RC-EDF. J.L. and J.W. constructed the experiment. S.C. performed the theoretical analyses. J.L. acquired the experimental data and carried out the data analyses. H.W., S.Z., L.Z., A.W., and L.W. provided technical support. All authors contributed to writing. J.W. finalized the paper. J.W. supervised the project.
The authors thank others for any contributions, whether it be direct technical help or indirect assistance. This work was supported by the National Key R&D Program of China (2018YFB1801803), the National Natural Science Foundation of China (NSFC) (61761130082, 11774116), the Royal Society-Newton Advanced Fellowship, the National Program for Support of Top-Notch Young Professionals, the Yangtze River Excellent Young Scholars Program, the Natural Science Foundation of Hubei Province of China (2018CFA048), the Key R&D Program of Guangdong Province (2018B030325002), the Open Fund of IPOC (BUPT) (IPOC2018A002), the Open Program from the State Key Laboratory of Advanced Optical Communication Systems and Networks (2020GZKF009), the Program for HUST Academic Frontier Youth Team (2016QYTD05), and the Fundamental Research Funds for the Central Universities (2019kfyRCPY037).
- L. Allen, M. W. Beijersbergen, R. J. C. Spreeuw, and J. P. Woerdman, “Orbital angular momentum of light and the transformation of Laguerre-Gaussian laser modes,” Physical Review A, vol. 45, no. 11, pp. 8185–8189, 1992.
- A. M. Yao and M. J. Padgett, “Orbital angular momentum: origins, behavior and applications,” Advances in Optics and Photonics, vol. 3, no. 2, pp. 161–204, 2011.
- S. Franke-Arnold, L. Allen, and M. Padgett, “Advances in optical angular momentum,” Laser & Photonics Reviews, vol. 2, no. 4, pp. 299–313, 2008.
- K. Dholakia and T. Čižmár, “Shaping the future of manipulation,” Nature Photonics, vol. 5, no. 6, pp. 335–342, 2011.
- L. Paterson, M. MacDonald, J. Arlt, W. Sibbett, P. E. Bryant, and K. Dholakia, “Controlled rotation of optically trapped microscopic particles,” Science, vol. 292, no. 5518, pp. 912–914, 2001.
- M. MacDonald, L. Paterson, K. Volke-Sepulveda, J. Arlt, W. Sibbett, and K. Dholakia, “Creation and manipulation of three-dimensional optically trapped structures,” Science, vol. 296, no. 5570, pp. 1101–1103, 2002.
- M. Padgett and R. Bowman, “Tweezers with a twist,” Nature Photonics, vol. 5, no. 6, pp. 343–348, 2011.
- S. Fürhapter, A. Jesacher, S. Bernet, and M. Ritsch-Marte, “Spiral phase contrast imaging in microscopy,” Optics Express, vol. 13, no. 3, pp. 689–694, 2005.
- M. P. J. Lavery, F. C. Speirits, S. M. Barnett, and M. J. Padgett, “Detection of a spinning object using light’s orbital angular momentum,” Science, vol. 341, no. 6145, pp. 537–540, 2013.
- L. Fang, M. J. Padgett, and J. Wang, “Sharing a common origin between the rotational and linear Doppler effects,” Laser & Photonics Reviews, vol. 11, no. 6, article 1700183, 2017.
- M. R. Dennis, R. P. King, B. Jack, K. O’Holleran, and M. J. Padgett, “Isolated optical vortex knots,” Nature Physics, vol. 6, no. 2, pp. 118–121, 2010.
- N. M. Elias II, “Photon orbital angular momentum in astronomy,” Astronomy & Astrophysics, vol. 492, no. 3, pp. 883–922, 2008.
- A. Mair, A. Vaziri, G. Weihs, and A. Zeilinger, “Entanglement of the orbital angular momentum states of photons,” Nature, vol. 412, no. 6844, pp. 313–316, 2001.
- J. Liu, I. Nape, Q. Wang, A. Vallés, J. Wang, and A. Forbes, “Multidimensional entanglement transport through single-mode fiber,” Science Advances, vol. 6, no. 4, article eaay0837, 2020.
- J. Wang, J.-Y. Yang, I. M. Fazal et al., “Terabit free-space data transmission employing orbital angular momentum multiplexing,” Nature Photonics, vol. 6, no. 7, pp. 488–496, 2012.
- N. Bozinovic, Y. Yue, Y. Ren et al., “Terabit-scale orbital angular momentum mode division multiplexing in fibers,” Science, vol. 340, no. 6140, pp. 1545–1548, 2013.
- J. Wang, “Advances in communications using optical vortices,” Photonics Research, vol. 4, no. 5, pp. B14–B28, 2016.
- J. W. Wang, “Data information transfer using complex optical fields: a review and perspective (Invited Paper),” Chinese Optics Letters, vol. 15, no. 3, article 030005, 2017.
- A. E. Willner, J. Wang, and H. Huang, “Applied physics. A different angle on light communications,” Science, vol. 337, no. 6095, pp. 655-656, 2012.
- A. E. Willner, H. Huang, Y. Yan et al., “Optical communications using orbital angular momentum beams,” Advances in Optics and Photonics, vol. 7, no. 1, pp. 66–106, 2015.
- J. Chu, D. Chu, and Q. Smithwick, “Encoding and multiplexing of 2D images with orbital angular momentum beams and the use for multiview color displays,” Research, vol. 2019, article 9564593, 11 pages, 2019.
- D. J. Richardson, J. M. Fini, and L. E. Nelson, “Space-division multiplexing in optical fibres,” Nature Photonics, vol. 7, no. 5, pp. 354–362, 2013.
- R. Ryf, S. Randel, A. H. Gnauck et al., “Mode-division multiplexing over 96 km of few-mode fiber using coherent 6 × 6 MIMO processing,” Journal of Lightwave Technology, vol. 30, no. 4, pp. 521–531, 2012.
- J. Liu, S. M. Li, L. Zhu et al., “Direct fiber vector eigenmode multiplexing transmission seeded by integrated optical vortex emitters,” Light: Science & Applications, vol. 7, no. 3, article 17148, 2018.
- C. Liu, K. Pang, Z. Zhao et al., “Single-end adaptive optics compensation for emulated turbulence in a bi-directional 10-Mbit/s per channel free-space quantum communication link using orbital-angular-momentum encoding,” Research, vol. 2019, article 8326701, 10 pages, 2019.
- J. Liu and J. Wang, “Polarization-insensitive PAM-4-carrying free-space orbital angular momentum (OAM) communications,” Optics Express, vol. 24, no. 4, pp. 4258–4269, 2016.
- A. Wang, L. Zhu, J. Liu, C. du, Q. Mo, and J. Wang, “Demonstration of hybrid orbital angular momentum multiplexing and time-division multiplexing passive optical network,” Optics Express, vol. 23, no. 23, pp. 29457–29466, 2015.
- S. Chen, J. Liu, Y. Zhao et al., “Full-duplex bidirectional data transmission link using twisted lights multiplexing over 1.1-km orbital angular momentum fiber,” Scientific Reports, vol. 6, no. 1, article 38181, 2016.
- J. Liu, L. Zhu, A. Wang et al., “All-fiber pre- and post-data exchange in km-scale fiber-based twisted lights multiplexing,” Optics Letters, vol. 41, no. 16, pp. 3896–3899, 2016.
- J. Liu, S. Li, Y. Ding et al., “Orbital angular momentum modes emission from a silicon photonic integrated device for km-scale data-carrying fiber transmission,” Optics Express, vol. 26, no. 12, pp. 15471–15479, 2018.
- A. Wang, L. Zhu, L. Wang, J. Ai, S. Chen, and J. Wang, “Directly using 8.8-km conventional multi-mode fiber for 6-mode orbital angular momentum multiplexing transmission,” Optics Express, vol. 26, no. 8, pp. 10038–10047, 2018.
- S. Ramachandran, P. Kristensen, and M. F. Yan, “Generation and propagation of radially polarized beams in optical fibers,” Optics Letters, vol. 34, no. 16, pp. 2525–2527, 2009.
- C. Brunet, P. Vaity, Y. Messaddeq, S. LaRochelle, and L. A. Rusch, “Design, fabrication and validation of an OAM fiber supporting 36 states,” Optics Express, vol. 22, no. 21, pp. 26117–26127, 2014.
- L. Zhu, G. Zhu, A. Wang et al., “18 km low-crosstalk OAM + WDM transmission with 224 individual channels enabled by a ring-core fiber with large high-order mode group separation,” Optics Letters, vol. 43, no. 8, pp. 1890–1893, 2018.
- S. Chen, S. Li, L. Fang, A. Wang, and J. Wang, “OAM mode multiplexing in weakly guiding ring-core fiber with simplified MIMO-DSP,” Optics Express, vol. 27, no. 26, pp. 38049–38060, 2019.
- Q. Kang, P. Gregg, Y. Jung et al., “Amplification of 12 OAM modes in an air-core erbium doped fiber,” Optics Express, vol. 23, no. 22, pp. 28341–28348, 2015.
- Y. Jung, E. L. Lim, Q. Kang et al., “Cladding pumped few-mode EDFA for mode division multiplexed transmission,” Optics Express, vol. 22, no. 23, pp. 29008–29013, 2014.
- J. Ma, F. Xia, S. Chen, S. Li, and J. Wang, “Amplification of 18 OAM modes in a ring-core erbium-doped fiber with low differential modal gain,” Optics Express, vol. 27, no. 26, pp. 38087–38097, 2019.
- Q. Kang, E. L. Lim, Y. Jung et al., “Accurate modal gain control in a multimode erbium doped fiber amplifier incorporating ring doping and a simple LP01 pump configuration,” Optics Express, vol. 20, no. 19, pp. 20835–20843, 2012.
- C. Jin, B. Ung, Y. Messaddeq, and S. LaRochelle, “Tailored modal gain in a multi-mode erbium-doped fiber amplifier based on engineered ring doping profiles,” in Proceedings Volume 8915, Photonics North 2013; 89150A, Ottawa, Canada, October 2013.
Copyright © 2020 Jun Liu et al. Exclusive Licensee Science and Technology Review Publishing House. Distributed under a Creative Commons Attribution License (CC BY 4.0).